BIOS Bug Report: IT8613E Super I/O Reset Across s2idle Sleep & _SB.PEP._DSM (EC0.UPHK) ACPI Exception on Beelink SER9 (SER9T409)
1. System & Firmware Identification
Product / Motherboard : Beelink SER9 (AZW SER9, Chassis/Board Version V1.0)
Processor / SoC : AMD Ryzen AI 9 HX 370 w/ Radeon 890M (Strix Point, Family 0×1A, Model 0×24)
Super I/O Chip : ITE IT8613E (DEVID = 0×8613, DEVREV = 0×0c) at config port 0×2e/0×2f via AMD FCH eSPI (0xFEC20000)
BIOS Vendor : American Megatrends International, LLC. (AMI Aptio V)
BIOS Version : SER9T409
BIOS Release Date : 06/23/2026 (SMBIOS 3.7, BIOS Revision 5.32)
Operating System Tested: Linux 7.2.11-200.nobara.fc44.x86_64 (Also impacts Windows 11 Modern Standby S0 Low Power Idle fan curve & hardware monitoring)
Serial Number : 
2. Executive Summary
When the Beelink SER9 enters and resumes from Modern Standby (s2idle / AMD S0i3), two compounding firmware bugs occur:
Bug 1 — IT8613E Super I/O (0×2e/0×2f) and Environment Controller (LDN 4 at 0×0a30) Reset to Power-On Defaults Across s2idle Without Re-initialization:
During initial BIOS POST, the firmware configures IT8613E Logical Device 4 (LDN 4, Environment Controller) with ACT (0×30) = 0×01, BASE (0×60/0×61) = 0×0a30, and BASE2 (0×62/0×63) = 0×0a20, and programs the Environment Controller (0×0a35/0×0a36) with the BIOS SmartGuardian fan curve, 16-bit fan tachometer enable (FAN_TAC2), and AMD TSI (AMDSI) CPU thermal input.
During s2idle sleep, the IT8613E chip resets to its hardware power-on defaults (LDN 4: ACT = 0×00 [Disabled], BASE = 0×0290, BASE2 = 0×0230), while the AMD FCH eSPI controller (MMIO 0xFEC20048 = 0×02000a00) continues decoding 0×0a00–0×0a3f.
On s2idle resume, the firmware never re-initializes IT8613E LDN 4 or its Environment Controller registers. Notice that _SB.PCI0.SBRG.SIO1.SIOS and SIOW in DSDT are only wired to legacy _PTS / _WAK (S3/S4/S5) and do not restore LDN 4 base addresses or EC fan/thermal registers.
Impact: After the first sleep/wake cycle, all reads from 0×0a30–0×0a37 return 0xFF, fan speed reporting drops permanently to 0 RPM until a reboot, and the BIOS SmartGuardian hardware fan curve in the IT8613E EC (0×13, 0×14, 0×16, 0×51, 0×68–0×6f) is wiped out to power-on reset defaults.
Bug 2 — _SB.PEP._DSM (SSDT28 / UPEP) Crashes with AE_NOT_EXIST in _SB.PCI0.SBRG.EC0.UPHK (DSDT) on Every s2idle Entry and Exit:
In DSDT, _SB.PCI0.SBRG.EC0 (PNP0C09) is disabled: Method (_STA) { Return (Zero) } and Name (OKEC, Zero). Consequently, no ACPI EmbeddedControl (ERAM) region handler is registered by the OS.
In SSDT28 (OEM Table ID: UPEP), the AMD LPS0 s2idle DSM (_SB.PEP.DSM, UUID 560de011-64ce-ce47-837b-1f898f9aa461) calls _SB.PCI0.SBRG.EC0.UPHK (ToInteger (Arg2)) at the beginning of _DSM.
Inside DSDT, UPHK checks If ((Arg0 >= 0×02) && (Arg0 <= 0×05)) and unconditionally writes SYSK = Arg0 (Field in OperationRegion (ERAM, EmbeddedControl, 0×00, 0xFF)) without checking If (OKEC) (unlike other methods in EC0 that guard ERAM accesses with If (OKEC)).
Impact: Every s2idle cycle aborts _SB.PEP.DSM with AE_NOT_EXIST on func:3 (Display Off), func:5 (Sleep Entry), and func:4 (Sleep Exit). When UPHK(4) aborts at SYSK = Arg0, it never reaches Case (0×04) { KBRS () } (which calls ENVW() to configure FCH eSPI 0xFEC20000), and _SB.PEP.DSM never completes its s2idle transitions.
3. Technical Evidence & Hardware Register Diff
3.1 Pre-Sleep vs. Post-s2idle Hardware Register Diff
Using a direct hardware diagnostic tool (reading AMD FCH eSPI MMIO at 0xFEC20000, IT8613E Super I/O configuration ports 0×2e/0×2f, and IT8613E EC ports 0×0a30–0×0a37) immediately before and after a 5-second s2idle cycle (rtcwake -m freeze -s 5):
` === fan2_input ===
-1171
+0
=== FCH eSPI MMIO @ 0xFEC20000 ===
0×00: ffffffff ffffffff ffffffff ffffffff
0×10: ffffffff ffffffff ffffffff 00000000
0×20: 00000000 00000000 0000a005 00000000
0×30: bf14007b 0012ff02 00000030 00000000
0×40: 00001f07 060003f8 02000a00 07ffff07
0×50: fec20200 00000000 00000000 00000000
-0×60: 000000ff 00000000 e400000e ff8fffff
+0×60: 000000ff 00000000 e400000e ff8cfff7
…
=== Super I/O Ports ===
SuperIO @ 0×2e: DEVID=0×8613 DEVREV=0×0c
Global 0×20..0×2f: 20:86 21:13 22:0c 23:40 24:00 25:00 26:02 27:00 28:00 29:01 2a:01 2b:48 2c:01 2d:00 2e:00 2f:00
- LDN 4 (EC): ACT(0×30)=0×01 BASE(0×60)=0×0a30 BASE2(0×62)=0×0a20
- LDN 4 (EC): ACT(0×30)=0×00 BASE(0×60)=0×0290 BASE2(0×62)=0×0230
LDN 4 0xf0..0xff: f0:80 f1:00 f2:00 f3:00 f4:e0 f5:00 f6:f0 f7:00 f8:03 f9:48 fa:00 fb:00 fc:00 fd:40 fe:00 ff:00
=== EC I/O @ 0×0a30 (0×0a35/0×0a36) ===
-inb(0×0a30..0×0a37): 19 19 19 19 19 55 40 19
-EC reg 0×0e (FAN_TAC2 LSB)=0×41, 0×19 (FAN_TAC2 MSB)=0×02
+inb(0×0a30..0×0a37): ff ff ff ff ff ff ff ff
+EC reg 0×0e (FAN_TAC2 LSB)=0xff, 0×19 (FAN_TAC2 MSB)=0xff`
Additionally, LDN 7 (GPIO) BASE (0×60/0×61) resets from 0×0a10 (pre-sleep) to 0×0000 (post-sleep), and when LDN 4 is manually re-enabled at 0×0a30 after s2idle, the internal EC registers at 0×0a35/0×0a36 are found in their power-on reset state:
EC Register (0x0a35/0x0a36) Description Pre-Sleep (BIOS POST) Post-s2idle (Reset Default) Consequence of Reset
0x00 Configuration Register 0x19 (Start = 1) 0x18 (Start = 0) ADC / monitoring stopped
0x0c Fan Tachometer 16-bit Enable 0x02 (FAN_TAC2 16-bit) 0x00 16-bit fan counter disabled
0x13 Fan Controller Main Control 0xa2 (FAN_TAC2 + FAN_CTL2 Auto) 0x80 FAN_TAC2 disabled; FAN_CTL2 forced to 100% full speed
0x14 Fan Control (Polarity) 0xc0 (Active-High) 0x40 (Active-Low) PWM polarity inverted
0x16 FAN_CTL2 PWM Control 0x80 (SmartGuardian Auto) 0x00 (Software Mode) SmartGuardian automatic thermal control disabled
0x51 Thermal Sensor Enable 0x40 (AMD TSI / PECI temp1) 0x00 (Disabled) CPU temperature input disabled (-128°C)
0x68–0x6f FAN_CTL2 SmartGuardian Table BIOS Setup fan curve 7f 7f 7f 3b 00 00 0f 3b Custom/BIOS fan curve lost
3.2 Kernel Log (dmesg) Showing _SB.PEP._DSM & EC0.UPHK Aborting During s2idle
Every s2idle cycle produces the following ACPI errors:
PM: suspend entry (s2idle)
ACPI Error: No handler for Region [ERAM] (000000009800da10) [EmbeddedControl] (20260408/evregion-131)
ACPI Error: Region EmbeddedControl (ID=3) has no handler (20260408/exfldio-261)
ACPI Error: Aborting method \_SB.PCI0.SBRG.EC0.UPHK due to previous error (AE_NOT_EXIST) (20260408/psparse-543)
ACPI Error: Aborting method \_SB.PEP._DSM due to previous error (AE_NOT_EXIST) (20260408/psparse-543)
ACPI: \_SB_.PEP_: failed to evaluate _DSM 560de011-64ce-ce47-837b-1f898f9aa461 rev:0 func:3 (0x6)
ACPI Error: No handler for Region [ERAM] (000000009800da10) [EmbeddedControl] (20260408/evregion-131)
ACPI Error: Region EmbeddedControl (ID=3) has no handler (20260408/exfldio-261)
ACPI Error: Aborting method \_SB.PCI0.SBRG.EC0.UPHK due to previous error (AE_NOT_EXIST) (20260408/psparse-543)
ACPI Error: Aborting method \_SB.PEP._DSM due to previous error (AE_NOT_EXIST) (20260408/psparse-543)
ACPI: \_SB_.PEP_: failed to evaluate _DSM 560de011-64ce-ce47-837b-1f898f9aa461 rev:0 func:5 (0x6)
ACPI Error: No handler for Region [ERAM] (000000009800da10) [EmbeddedControl] (20260408/evregion-131)
ACPI Error: Region EmbeddedControl (ID=3) has no handler (20260408/exfldio-261)
ACPI Error: Aborting method \_SB.PCI0.SBRG.EC0.UPHK due to previous error (AE_NOT_EXIST) (20260408/psparse-543)
ACPI Error: Aborting method \_SB.PEP._DSM due to previous error (AE_NOT_EXIST) (20260408/psparse-543)
ACPI: \_SB_.PEP_: failed to evaluate _DSM 560de011-64ce-ce47-837b-1f898f9aa461 rev:0 func:4 (0x6)
PM: suspend exit
3.3 Faulty ASL Code in DSDT and SSDT28 (UPEP)
In SSDT28 (OEM Table ID: UPEP), _SB.PEP._DSM for UUID 560de011-64ce-ce47-837b-1f898f9aa461:
ElseIf ((Arg0 == ToUUID ("560de011-64ce-ce47-837b-1f898f9aa461")))
{
If (CondRefOf (\_SB.PCI0.SBRG.EC0.UPHK))
{
\_SB.PCI0.SBRG.EC0.UPHK (ToInteger (Arg2))
}
Switch (ToInteger (Arg2))
{
Case (0x00) { ... }
Case (0x03) { M000 (0x3E03); Return (Zero) }
Case (0x04) { M000 (0x3E04); Return (Zero) }
Case (0x05) { M000 (0x3E05); Return (Zero) }
...
}
}
In DSDT, under Device (EC0):
Device (EC0)
{
Name (_HID, EisaId ("PNP0C09"))
Method (_STA, 0, NotSerialized)
{
Return (Zero)
}
Name (OKEC, Zero)
OperationRegion (ERAM, EmbeddedControl, Zero, 0xFF)
Field (ERAM, ByteAcc, NoLock, Preserve)
{
...
KBFG, 8,
SYSK, 8,
...
}
...
Method (UPHK, 1, NotSerialized)
{
M460 ("PLA-ASL-\\_SB.PCI0.SBRG.EC0.UPHK Start\n", Zero, Zero, Zero, Zero, Zero, Zero)
Arg0 &= 0x0F
ECPC ((0xF0 | Arg0))
If (((Arg0 >= 0x02) && (Arg0 <= 0x05)))
{
SYSK = Arg0 // <-- BUG: Unconditional write to ERAM when EC0._STA == 0 (OKEC == 0)!
}
Switch (ToInteger (Arg0))
{
Case (0x03)
{
}
Case (0x04)
{
KBRS () // <-- Never reached because SYSK = Arg0 aborts with AE_NOT_EXIST!
}
}
M460 ("PLA-ASL-\\_SB.PCI0.SBRG.EC0.UPHK End\n", Zero, Zero, Zero, Zero, Zero, Zero)
}
}
4. Live Recovery Verification
We verified on the live system after s2idle that re-programming IT8613E LDN 4 (0×2e/0×2f) and the EC registers (0×0a35/0×0a36) immediately restores both fan RPM reporting and SmartGuardian PWM fan control without a reboot:
- Enter Super I/O MB PnP Mode on 0×2e (0×87, 0×01, 0×55, 0×55).
- Select LDN 4 (0×07 = 0×04) and restore:
- 0×60 = 0×0a, 0×61 = 0×30 (BASE = 0×0a30)
- 0×62 = 0×0a, 0×63 = 0×20 (BASE2 = 0×0a20)
- 0×30 = 0×01 (ACT = 0×01)
- Exit MB PnP Mode (0×02, 0×02).
- Restore the IT8613E Environment Controller (0×0a35/0×0a36) registers (0×0c = 0×02, 0×14 = 0xc0, 0×16 = 0×80, 0×13 = 0xa2, 0×51 = 0×40, 0×00 = 0×19).
- Immediately after restoration, 0×0a30–0×0a37 stops returning 0xFF and fan2_input reports live RPM again (865 RPM idle / 2509 RPM full duty cycle).
5. Recommended BIOS Fixes for Beelink Engineering
Guard ERAM Accesses in _SB.PCI0.SBRG.EC0.UPHK (and KBRS / _Q70) with If (OKEC) in DSDT:
- In _SB.PCI0.SBRG.EC0.UPHK:
If (OKEC)
{
If (((Arg0 >= 0x02) && (Arg0 <= 0x05)))
{
SYSK = Arg0
}
}
- Similarly, in KBRS (), guard Local0 = KBFG (which also reads from ERAM) with If (OKEC) (or read from the system-memory KBFG variable) so UPHK(4) does not abort with AE_NOT_EXIST when EC0._STA returns 0.
Preserve or Re-initialize IT8613E (SIO1) Across s2idle (S0i3):
- Hardware/GPIO Power Rail Check: If IT8613E power or LRESET# is gated during S0i3 / s2idle, either keep the Super I/O rail powered in S0i3 or re-run the IT8613E initialization sequence on s2idle resume.
- ACPI / Firmware s2idle Resume Hook: In the s2idle resume path (_SB.PEP.DSM Case (0×04) or _SB.PCI0.SBRG.SIO1.SIOW called from _SB.PEP.DSM Case (0×04)):
- Unlock IT8613E at 0×2e (ENFG(0×04)), restore LDN 4 (IOAH = 0×0A, IOAL = 0×30, IOH2 = 0×0A, IOL2 = 0×20, ACTR = 0×01) and LDN 7 (IOAH = 0×0A, IOAL = 0×10), and exit config mode (EXFG()).
- Restore the IT8613E Environment Controller (0×0a35/0×0a36) registers programmed during POST (including 0×0c 16-bit fan counter enable, 0×13/0×14/0×16 SmartGuardian fan control, 0×51 & 0×90–0×9f AMD TSI thermal input, 0×68–0×6f BIOS Setup SmartGuardian fan curve, and 0×00 Start monitoring bit).
Thank you!