BIOS Bug Report: Immediate s2idle Sleep Abort Caused by Floating FCH GPIO 3 & Ghost PS/2 Keyboard (PNP0303) _PRW Wake on Beelink SER9 (SER9T409)
1. System & Firmware Identification
Product: Beelink SER9 (AZW SER9, Chassis V1.0)
SoC: AMD Ryzen AI 9 HX 370 w/ Radeon 890M (Strix Point)
BIOS Version: SER9T409 (06/23/2026)
OS: Linux Kernel 6.10+ / 7.x (impacts all Linux distributions using standard modern standby s2idle / S0i3)
Serial Number: 
2. Problem Description
When attempting to put the Beelink SER9 to sleep (systemctl suspend or echo freeze > /sys/power/state), the machine immediately aborts sleep within 80–100 milliseconds and wakes back up to the desktop.
Because modern AMD Zen 5 (Strix Point) platforms exclusively use Modern Standby (s2idle / S0i3) and no longer support legacy S3, any unhandled or floating interrupt line with wake capability enabled will abort sleep before the platform reaches low-power idle.
3. Root Cause Analysis & Technical Evidence
Bug A: FCH GPIO 3 Configured with Wake-Enable (0xFED8150C / IRQ 9)
In the AMD Promontory/FCH GPIO controller, GPIO 3 (MMIO register 0xFED8150C, managed by the kernel’s pinctrl_amd on IRQ 9) is left with its interrupt unmasked and wake-enable bit active in hardware, but has no corresponding active ACPI device, debouncing, or event handler.
In dmesg, the sleep cycle immediately terminates with:
PM: suspend-to-idle
...
PM: suspend-to-idle aborted: wake source IRQ 9
PM: suspend exit
Verification: Clearing the wake-enable bit in FCH GPIO register 0xFED8150C (via ACPI method And (CTRL, Not (0×02), CTRL)) stops the GPIO 3 wake abort entirely.
Bug B: Phantom PS/2 Keyboard Device (PNP0303 / serio0) Defined with _PRW Wake Capability
In DSDT, under _SB.PCI0.SBRG, there is a legacy PS/2 keyboard definition:
Device (PS2K)
{
Name (_HID, EisaId ("PNP0303"))
Name (_CID, EisaId ("PNP030B"))
Name (_CRS, ResourceTemplate ()
{
IO (Decode16, 0x0060, 0x0060, 0x00, 0x01)
IO (Decode16, 0x0064, 0x0064, 0x00, 0x01)
IRQNoFlags () {1}
})
Method (_PRW, 0, NotSerialized)
{
Return (Package () { 0x18, 0x03 }) // <-- BUG: Declares PS/2 KBC as a system wake source!
}
}
The Issue: The Beelink SER9 is a mini-PC that has no physical PS/2 port. Because the DSDT includes _PRW, the OS kernel enables /sys/bus/serio/devices/serio0/power/wakeup. Spurious noise on the floating IRQ 1 line triggers an immediate resume event.
Verification: Setting echo disabled > /sys/bus/serio/devices/serio0/power/wakeup prevents the keyboard controller from waking the machine.
4. Expected Behavior & Fix for BIOS Engineering
Remove PRW from Device (PS2K) in DSDT: Since the board has no PS/2 port, PS2K should not declare wake capabilities (PRW). Removing _PRW from Device (PS2K) prevents the OS from arming serio0 as a system wakeup source.
Properly Disarm / Mask Unused FCH GPIO Wake Pins in _PTS / _LPI: Ensure unused GPIO lines (specifically FCH GPIO 3 at 0xFED8150C) have their wake-enable and interrupt trigger bits cleared or masked before entering low-power idle states (S0i3).
Thank you!