Hello Beelink Support,
I’m experiencing a persistent DisplayPort MST compatibility problem with my Beelink SER5 mini PC. I’ve performed extensive troubleshooting and would appreciate technical assistance determining whether this is a hardware limitation, BIOS configuration issue, or firmware problem.
Computer Specifications
- Manufacturer: Beelink / AZW
- Model: SER5-L-16500EJ0W64PRO-DP/XB
- Processor: AMD Ryzen 5 5500U
- Graphics: AMD Radeon integrated graphics
- Motherboard: AZW SER V3.0
- Current BIOS: SERAL201 (April 8, 2025)
- Operating System: Windows 11 Pro
- AMD Graphics Software: Adrenalin Edition 26.5.2 (WHQL)
- DisplayPort: Advertised as DP 1.4
Monitors
I am using two Acer monitors:
- Monitor 1: Acer SA243Y G0
- Monitor 2: Acer SB243Y G0
- Both operate at 1920 × 1080, 60 Hz, 8-bit color.
Problem Description
I want to operate both monitors independently through a single DisplayPort connection using a DisplayPort-to-dual-HDMI MST hub.
I have tried two different adapters:
- UANTIN DisplayPort-to-Dual-HDMI MST Adapter — Amazon ASIN B0CNP2QDL4
- Buerlaseul DisplayPort-to-Dual-HDMI MST Adapter — Amazon ASIN B0GY3DL6Q5
Both adapters exhibit identical problems.
When one monitor is connected to either HDMI output on the MST adapter, it works normally.
However, connecting the second monitor causes both monitors to immediately lose their video signals. They eventually report “No Signal” and enter standby.
Disconnecting the second monitor restores video to the first monitor.
Windows produces device connection and disconnection sounds when the second monitor is connected.
Current Working Configuration
Both monitors function correctly when connected through separate computer outputs:
- Monitor 1: DisplayPort → MST adapter → HDMI
- Monitor 2: Computer’s built-in HDMI output
Windows correctly recognizes both displays and operates them in extended desktop mode.
Important Finding — Adapter Successfully Tested on Another Computer
I connected the current Buerlaseul MST adapter to a laptop equipped with Intel HD Graphics 620.
The adapter worked perfectly.
The laptop successfully operated three independent displays:
- Laptop screen: Display 1
- Acer SA243Y G0: Display 2
- Acer SB243Y G0: Display 3
Both Acer monitors operated simultaneously at 1920 × 1080, approximately 60 Hz, 8-bit RGB.
This confirms that the adapter, HDMI cables, and monitors can operate correctly together in MST extended desktop mode.
Troubleshooting Already Completed
- Tested both HDMI outputs individually — Both work.
- Tested both monitors individually through the adapter — Both work.
- Tested two different MST adapters — Identical failures.
- Supplied external USB power using a 5V/2A power adapter — No improvement.
- Changed both monitors from 10-bit to 8-bit color — No improvement.
- Tested lower monitor resolutions — No improvement.
- Confirmed Windows is configured for extended displays.
- Updated AMD graphics drivers to Adrenalin 26.5.2 — No improvement.
- Restarted Windows after updating the graphics driver.
- Reset the graphics driver using Windows + Ctrl + Shift + B — No improvement.
- Examined Windows Device Manager and monitor detection.
- Inspected BIOS graphics configuration menus, including AMD PBS, AMD CBS, and NBIO options — No identifiable MST enable/disable setting was found.
Additional Finding — DisplayPort Link Speed
AMD Adrenalin reports the following when one monitor is operating through the MST adapter:
Current Link Settings: 1.62 Gbps × 4
This corresponds to DisplayPort RBR mode, providing approximately 5.18 Gbps of usable bandwidth.
I understand that DisplayPort link speed is negotiated dynamically and may increase when additional bandwidth is required.
However, I cannot determine whether the Beelink successfully negotiates a higher link rate when both monitors are connected.
BIOS Information
My current BIOS is SERAL201, dated April 8, 2025.
I located Beelink’s SERAL202 update for the SER5 5500U with 2.5G Ethernet.
However, during the attempted update, the AMI flashing utility displayed:
Check RomLayout: Changed
The ROM file information does not match the system BIOS
I canceled the update rather than force it.
The computer remains on SERAL201.
I have separately contacted Beelink support regarding this BIOS compatibility warning.
Questions for Beelink Technical Support
Does the SER5 Ryzen 5 5500U, specifically model SER5-L-16500EJ0W64PRO-DP/XB, support DisplayPort Multi-Stream Transport (MST) through its physical DisplayPort output?
If MST is supported, should the computer be capable of operating two independent 1920 × 1080, 60 Hz monitors through a single DisplayPort-to-dual-HDMI MST hub?
Is there a known BIOS, firmware, or hardware limitation affecting MST operation on this SER5 model?
Is there a BIOS setting that enables MST or controls DisplayPort link-speed negotiation?
Is SERAL202 expected to address any DisplayPort or MST compatibility problems?
Are there specific AMD graphics drivers or other manufacturer-provided updates recommended for MST operation?
Given that two different MST adapters exhibit identical failures on the Beelink, while the current adapter functions perfectly on another computer, I believe the issue is specific to the Beelink’s DisplayPort MST implementation or configuration.
I would appreciate a technical explanation and any recommended corrective action.
Thank you for your assistance.